# EndoArt® Expert

> Single-File Reciprocating

- **Manufacturer:** İnci Dental (Turkey)
- **Motion:** Reciprocating
- **Alloy:** Gold/Blue Heat-Treated NiTi
- **Key feature:** Reciprocating system (150° CCW / 30° CW) with 04/06 taper options and S-shaped cross-section

## Specifications

### Expert Gold

| File | Tip (mm) | Taper | Length | Cross-section | Motion | Speed (rpm) | Torque | Role |
| --- | --- | --- | --- | --- | --- | --- | --- | --- |
| R25 | 0.25 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R30 | 0.30 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R35 | 0.35 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R40 | 0.40 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R50 | 0.50 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |

### Expert Blue

| File | Tip (mm) | Taper | Length | Cross-section | Motion | Speed (rpm) | Torque | Role |
| --- | --- | --- | --- | --- | --- | --- | --- | --- |
| R25 | 0.25 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R30 | 0.30 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R35 | 0.35 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R40 | 0.40 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |
| R50 | 0.50 | 4% or 6% | 21mm, 25mm, 31mm | S-shaped | Reciprocating | Reciprocating | — | — |

## Protocol

### Glide Path

1. **Establish Glide Path** — Establish a glide path with hand files before reciprocating shaping. Use standard scouting and negotiation technique per your training.
   - Expert Blue files can be pre-bent due to controlled memory

### Shaping

1. **Reciprocating Shaping** — Select file size based on canal anatomy. Use reciprocating mode (150° CCW / 30° CW). Available: R25, R30, R35, R40, R50 in both Gold and Blue, with 04 and 06 taper options. _(File: Expert Gold or Blue (R25–R50) · Reciprocating (150° CCW / 30° CW) · 150° CCW / 30° CW)_
   - Available in both Gold and Blue heat treatment
   - Can upsize if file is loose at WL
   - ⚠ Never use continuous rotation

### Finishing

1. **Verify Preparation** — Verify apical preparation and proceed with obturation.
   - S-shaped cross-section provides effective debris removal
   - Verify tug-back with master cone before obturation

## Clinical Tips

- Gold heat treatment: 2x cyclic fatigue resistance vs conventional NiTi (manufacturer data, not independently verified)
- Blue heat treatment: 4x cyclic fatigue resistance vs conventional NiTi (manufacturer data, not independently verified)
- Blue files can be pre-bent before canal entry due to controlled memory
- Single-file system reduces cross-contamination risk
- Reciprocating motion (150° CCW / 30° CW) reduces cyclic fatigue
- S-shaped cross-section for debris removal
- Each file size available in both 04 and 06 taper options
- Reuse/sterilization: not specified in catalog — contact manufacturer for reprocessing instructions

## Warnings

- Must use reciprocating motor settings — never continuous rotation
- Inspect for distortion or deformation before each use — discard if defective
- Reuse and sterilization protocol not established in publicly available catalog — verify with manufacturer

## Best for

- single-file reciprocating
- cost-effective
- reduced cross-contamination

## Technical profile

- **Category:** single-file-reciprocating
- **Heat treatment:** Gold Heat-Treated — Gold or Blue heat treatment options available
- **Manufacturing method:** ground
- **Pre-bendable:** yes
- **Motor:** any-reciprocating
- **Reciprocation angles:** 150° CCW / 30° CW
- **Glide path requirement:** optional
- **Canal suitability:** Curvature: mild, moderate, severe; Canal size: narrow, normal, wide; Calcified canals: no; Retreatment: no; Conservative access: no
- **Content revision:** 2026-02-16

## FAQ

**What alloy is EndoArt Expert made from?**

EndoArt® Expert is manufactured from Gold/Blue Heat-Treated NiTi.

**How many files are in the EndoArt Expert sequence?**

The EndoArt® Expert system includes 10 files: R25, R30, R35, R40, R50, R25, R30, R35, R40, R50.

**What is the EndoArt Expert file sequence?**

EndoArt® Expert offers these files: R25, R30, R35, R40, R50. One shaping file is selected per canal according to the DFU; the protocol section above shows the starting file.

**What motion type does EndoArt Expert use?**

EndoArt® Expert uses reciprocating motion.

**What cases is EndoArt Expert best for?**

EndoArt® Expert is best suited for: single-file reciprocating, cost-effective, reduced cross-contamination.

**What speed and torque settings are recommended for EndoArt Expert?**

EndoArt® Expert uses reciprocating motion with manufacturer-specific motor settings (refer to official DFU for exact parameters).

## References

- [Manufacturer instructions for use (DFU/IFU)](https://endoart.com.tr/assets/front-face/catalog/endoart-katalog-en.pdf)

## Related

- [HTML page](https://endo-guide.app/system/endoart-expert)
- [Manufacturer hub: Inci Dental (Turkey) Systems](https://endo-guide.app/manufacturer/inci-dental)
- [Compare systems](https://endo-guide.app/compare)
- Other languages: [Türkçe](https://endo-guide.app/tr/system/endoart-expert.md) · [Español](https://endo-guide.app/es/sistema/endoart-expert.md)
- [llms.txt](https://endo-guide.app/llms.txt) · [EndoGuide (Markdown)](https://endo-guide.app/index.md)

---

_Educational reference for dental professionals. Always confirm settings against the official manufacturer instructions for use before clinical procedures._