HyFlex® CM
Pre-bendable like stainless steel with enhanced cyclic fatigue resistance vs conventional NiTi (manufacturer reports up to 300%, in-house bench data)
AlloyCM-Wire (Controlled Memory NiTi)File6Verified
Specifications
Tap icons for term definitions
| File | Tip | Taper | Speed rpm | Torque Ncm |
|---|---|---|---|---|
| Orifice Opener 25/.08 | 0.25 | 8% | 500 | 2.5 |
| 20/.04 | 0.20 | 4% | 500 | 2.5 |
| 25/.04 | 0.25 | 4% | 500 | 2.5 |
| 20/.06 | 0.20 | 6% | 500 | 2.5 |
| 30/.04 | 0.30 | 4% | 500 | 2.5 |
| 40/.04 | 0.40 | 4% | 500 | 2.5 |
Clinical Tips
CM-Wire has no shape memory at room temperature — files can be pre-bent like stainless steel to follow abrupt curvatures
Spiral lengthening under stress is a built-in safety feature that prevents wall binding and reduces fracture risk
Shape regenerates during autoclaving — visual inspection after autoclaving serves as a discard indicator
All files use the same motor settings: 500 RPM and 2.5 Ncm (EU IFU; US IFU specifies 2.4 Ncm)
Files may arrive slightly bent due to CM properties — correct by hand before use
A hybrid technique combining .04 and .06 tapers is the IFU-recommended approach
Warnings
- If spirals rewind in the opposite direction during use, the file is plastically deformed — discard immediately
- If spirals remain lengthened after autoclaving, the file must be discarded
- Inspect files before and after every use for visible changes in material or shape
- Do not use on patients with known nickel or titanium allergy (per 2025 IFU)
- Follow IFU reprocessing instructions — condition-based reuse, no fixed maximum cycle count
Obturation Techniques
Single cone, warm vertical, carrier-based & lateral compaction
Protocol
01Glide Path
02Shaping
03Finishing
Related Systems
From Coltene Systems
Manufacturer page
Coltene SystemsOther continuous rotation systems
Motion category
Continuous RotationCollections
Clinical guides
Frequently Asked Questions
01What alloy is HyFlex CM made from?
01
What alloy is HyFlex CM made from?
Answer
HyFlex® CM is manufactured from CM-Wire (Controlled Memory NiTi) with cm-wire heat treatment.
02How many files are in the HyFlex CM sequence?
02
How many files are in the HyFlex CM sequence?
Answer
The HyFlex® CM system includes 6 files: Orifice Opener 25/.
- 0108, 20/.
- 0204, 25/.
- 0304, 20/.
- 0406, 30/.
- 0504, 40/.
- 0604.
03What motion type does HyFlex CM use?
03
What motion type does HyFlex CM use?
Answer
HyFlex® CM uses continuous rotation motion.
04What cases is HyFlex CM best for?
04
What cases is HyFlex CM best for?
Answer
HyFlex® CM is best suited for: curved canals requiring pre-bent files, anatomical shaping with multiple sizing options, reusable with autoclave regeneration.
05What speed and torque settings are recommended for HyFlex CM?
05
What speed and torque settings are recommended for HyFlex CM?
Answer
Recommended settings: 500 RPM and 2.
- 015 Ncm across the file sequence (refer to official DFU for full per-file parameters).
Reviewed by
Uzm. Dt. Levent Yüksel
DDS · Endodontist
Independently authored and clinically reviewed.
Powered by:Uzm. Dt. Levent Yüksel